Parts and parts

2nevets2nevets Posts: 84Member
edited June 2017 in Parts & Pieces
I purchased all of Don Mowry's parts- I prefer to sell the whole lot in one shot but will sell off pieces- I dont have a parts book so I will need some kind of help for the trim pieces.Here are just a couple of pics
I have 3 small  truck loads
«13

Comments

  • KustomKreepsKustomKreeps Posts: 327Member
    dont happen to have the side stainless for a 51 four door hornet would you? complete left and right side.
    Also some door sills to suit a 49 four door.

    thats a lot of old treasure man.
  • 2nevets2nevets Posts: 84Member
    yes on the sills-fair shape at best-need measurements and pics on the trim
  • 2nevets2nevets Posts: 84Member
    I too own a Hudson-its not just about the money
  • 01jeffrey01jeffrey Posts: 4Member
    are you located near Richmond va.?
  • charles4dcharles4d Posts: 497Expert Adviser
    Car has a new York tag on it ???
  • iceblade10iceblade10 Posts: 448Member
    Steven, do you have any Twin H Power emblems for the trunk?
  • 2nevets2nevets Posts: 84Member
    01jeffrey said:
    are you located near Richmond va.?
    wallkill Ny
  • 2nevets2nevets Posts: 84Member

    charles4d said:
    Car has a new York tag on it ???
    yes -why?
  • airbrushguyairbrushguy Posts: 305Member
    I'm trying to build an intake for a supercharger system I'm putting on my '49. I could use an air cleaner to cut up. 
    How much would you want for the worst looking one you have, like the one I have circled in the attached pic?
    I'm in NJ 07506
    Thanks
  • duncanduncan Posts: 828Expert Adviser
    I am looking for the ss trim strip and support for the hood scoop for our 54 Hornet  Ray
  • 2nevets2nevets Posts: 84Member
    duncan said:
    I am looking for the ss trim strip and support for the hood scoop for our 54 Hornet  Ray
    pic?
  • 2nevets2nevets Posts: 84Member
    I'm trying to build an intake for a supercharger system I'm putting on my '49. I could use an air cleaner to cut up. 
    How much would you want for the worst looking one you have, like the one I have circled in the attached pic?
    I'm in NJ 07506
    Thanks
    I am open to realistic offers
  • DoctorvauxDoctorvaux Posts: 33Member
    Hi, I am looking for a pair of rear fenders for a 1948-1950 2 door. I am also looking for a rocker panel for the passenger side.  Do you have any please? There appeared to be some fenders in one of the pictures, but I could not see if if they were for the 48-50 models.  Thank you.
  • 2nevets2nevets Posts: 84Member
    I have a set but I thought all stepdown coupes were the same?
  • GlowplugGlowplug Posts: 1,779Expert Adviser
    2nevets - the rear quarters for 48-53 are all bolt on, BUT the bumper cutout at the rear of the fender makes them different for select years.
  • DoctorvauxDoctorvaux Posts: 33Member
    There is a bluey/green rear fender in your picture with a hole for the rear lamp, so I would suspect that one is for a 52/53. If you have fenders without the hole and with the cut away for the rear bumper, then they would be for earlier cars. Please let me know if you have the early ones. Thamk you.
  • 2nevets2nevets Posts: 84Member
    2nevets - the rear quarters for 48-53 are all bolt on, BUT the bumper cutout at the rear of the fender makes them different for select years.
    thanks for the headsup!
  • 2nevets2nevets Posts: 84Member

    There is a bluey/green rear fender in your picture with a hole for the rear lamp, so I would suspect that one is for a 52/53. If you have fenders without the hole and with the cut away for the rear bumper, then they would be for earlier cars. Please let me know if you have the early ones. Thamk you.
    I do-how bad are yours? mine need some work
  • DoctorvauxDoctorvaux Posts: 33Member
    My fenders have already been repaired, but not very well. However I was hoping to find some better panels without dents or rust. How much work do the your fenders need ? The red fender in the picture appeared to be quite solid ? I live in the UK so I was hoping to find panels that were quite good to make it worthwhile to ship them all this way.  Do you have any rocker panels for a 2 door ?
    Thank you.
  • 2nevets2nevets Posts: 84Member
    My fenders have already been repaired, but not very well. However I was hoping to find some better panels without dents or rust. How much work do the your fenders need ? The red fender in the picture appeared to be quite solid ? I live in the UK so I was hoping to find panels that were quite good to make it worthwhile to ship them all this way.  Do you have any rocker panels for a 2 door ?
    Thank you.
    These are not worth the trip with the exception of the red one-
  • dave11dave11 Posts: 134Expert Adviser

    looking for a Twin H intake for a 308, don't need the carbs or linkage


    Dave

  • 2nevets2nevets Posts: 84Member
    I have a couple but I don't think they are for the 308
  • rkee0308rkee0308 Posts: 23Member
    I'm not sure of what all you have but if you have any trim for the hood of a 1946 Pickup I would be very interested. Also looking for a newer year steering column out of a step down to utilize for the turnsignal controls in my truck. 

    V/R,

    Ryan
  • 2nevets2nevets Posts: 84Member
    I believe I have a column
  • hudsonjet54hudsonjet54 Posts: 30Member
    Do you have any jet parts?
  • 2nevets2nevets Posts: 84Member
    I have a bunch of 54 jet trim
  • hudsonjet54hudsonjet54 Posts: 30Member
    Do u have pics
  • 2nevets2nevets Posts: 84Member
    No not yet
  • 2nevets2nevets Posts: 84Member
    I will be vending at fall carlisle if anyone needs anything
  • jjbubaboyjjbubaboy Posts: 816Senior Contributor
    Hey,
    Whats in the collection for overdrive transmissions?
    Thanks,
    J
Sign In or Register to comment.